Porsche 997 Gen 2 Suspension Upgrades 2010 to 2012

Porsche 997 Gen 2 - Suspension Upgrades - 2010 to 2012

  • EuroCupGT Front Tension Rods 997 Carrera Turbo / 987 Boster & Cayman 2005-2012

    SKU:7796

    3-5 Days 3-5 Days
    EuroCupGT uprated Front suspension tension bars replace the cast aluminium arms & allow for neutral adjustment when setting up your cars geometry. The rubber bushing is replaced with a Rose Joint to allow for more accurate handling. Fits the following: Boxster 987 Front Only Cayman 987 Front Only All 997 Models inc GT3 & Turbo Front Only
    £295.00 inc VAT £245.83 ex VAT
  • Spring Caps All Coil Over Applications & Billet Top Mounts GT3 RS 944 & 968 M030

    SKU:17128

    In Stock In Stock
    On applications using Adjustable Camber Plates Front & Rear. With spring ID of 62mm 2 1/4" using Spring Top Hats. Sold as a set of two. For all Spax & Bilstein B9 & B12 for 964 993 996 & 977 Turbo, GT3, RS. 924/944/968 M030. Boxster & Cayman R / GT4 etc
    £119.99 inc VAT £99.99 ex VAT
  • GT3 Cup FIXED COFFIN ARM BUSHING 996 997 Carrera Turbo 986 987 Boxster & Cayman

    SKU:SR088

    In Stock In Stock
    Not all suspension upgrades will require an adjustable castor / camer arm bushing like the SR087, thus the STOMSKI RACING's Fixed Thrust Arm Bushings provide the perfect solution for your application a standard Geometry setting is all that is required to prevent unpredictable camber changes.  Installing these high quality 6061 aluminum anodized bushings will provide better feedback and handling without leading to unwanted road noise on either your dedicated track car or daily driver.  By upgrading to STOMSKI RACING's Fixed Thrust Arm Bushings for all four control arms on your car, unwanted suspension changes caused by the stock flexible bushings will be a thing of the past, and thus your lap times will improve as your handling increases.  Fits; Front; All 996 & 986 Boxster. Rear; All 996 / 997 Carrera / GT3 / Turbo / GT2, 986 / 987 Boxster, and Cayman.  Sold as One set for 1 wishbone. ( 2 kits needed per axle ).
    £84.84 inc VAT £70.70 ex VAT
  • EuroCupGT 997 987 Carbon Strut Brace Carrera Turbo C4S GT3 Boxster Cayman 05-12

    SKU:1338

    In Stock In Stock
    This EuroCupGT Carbon Fibre strut brace is more rigid & significantly lighter than the steel ones. All Models 2005 -2012 It is fully adjustable to make fitting easy. All parts required to fit are included. The overall weight is around 900g
    £139.98 inc VAT £116.65 ex VAT
  • EuroCupGT Adjustable Rear Upper Control Arm Kit 996 / 997 Carrera, GT3 & Turbo

    SKU:7370

    In Stock In Stock
    Set of 4 Heave duty adjustable rear upper control arms. Ideal for Camber set ups and clearance, when using larger wheel & tyre sizes where Geometry is limited with standard control arms. All models 1998-2012
    £399.60 inc VAT £333.00 ex VAT
  • Agency Power Rear Adjustable Anti Roll Bar Drop Links 997 2005-2012

    SKU:APRX8205

    In Stock In Stock
    997/S / 997TT, GT2/3 & RS Rear adjustable Anti Roll bar drop links 2005-2012 ( Also fits All 996 models 98-2004 ) Per Pair (2) To complete suspension upgrades, these sway bar links to go hand and hand with the solid AP Anti Roll bars or Oem bars along with the AP rear control arm kit. Roll bar links offer you adjustability for setting up the suspension, these will enable you to properly corner weight your car for optimal handling. The 6061 CNC machined centres have flats cut in place for easy access for adjustments, one of the most over looked parts of suspension is the spherical rod ends. Agency Powers spherical rod ends are designed in stainless steel and have a Teflon liner sold in pairs for all 997 2004-2012 cars ( Also fits 996 models )
    £179.99 inc VAT £149.99 ex VAT
  • GT3 CUP / RSR ADJUSTABLE CASTOR THRUST BUSH FOR COFFIN ARM

    SKU:SR087

    3-5 Days 3-5 Days
    Whether doing a complete suspension upgrade, eliminating the overly-compliant rubber thrust arm bushings that lead to unpredictable camber changes, or searching for more range of adjustment for your suspension, STOMSKI RACING's Adjustable Thrust Arm Bushings are the answer to your needs.  Installing these high quality 6061 aluminum anodized bushings will provide better feedback and handling without leading to unwanted road noise on either your dedicated track car or daily driver.  By upgrading to STOMSKI RACING's Adjustable Thrust Arm Bushings for all four control arms on your car, unwanted suspension changes caused by the standard flexible bushings will be a thing of the past, and thus your lap times will improve as your handling increases.  Fits; Front All 996 / 986 Boxster. Rear; All 996 / 997 Carrera / GT3 / Turbo / GT2, 986 / 987 Boxster, and Cayman.  Sold as One set for 1 wishbone. ( 2 kits needed per axle )
    £94.92 inc VAT £79.10 ex VAT
  • Front Top Mount 997 C4 / C4S & 997 Turbo RIGHT 2005-2012

    SKU:11358

    In Stock In Stock
    OEM Top Mount for 4 wheel drive cars only. Handed
    £85.99 inc VAT £71.66 ex VAT
  • H&R Lowering Spring Kit 996 / 997 Cabriolet 1998-2012

    SKU:5003CAB

    3-5 Days 3-5 Days
    High Quality Smooth & progressive ( set of 4)
    £326.44 inc VAT £272.03 ex VAT
  • Stomski Racing Adjustable Rear Control Arm kit All 996 997 models 1998-2012

    SKU:AP996200

    In Stock In Stock
    Set of 4 Billet Alloy Motorsport grade upper control arms fit on the rear of your car and help in adjusting camber and toe. In additional to being fully adjustable, these control arms offer increased rigidity from the replacement of the factory rubber bushing with spherical bearing ends. Fits all 996 & 997 Models inc GT3 & Turbo 1998-2012
    £599.99 inc VAT £499.99 ex VAT
  • Elephant Racing Adjustable Rear Toe Links for Lowered Cars 996 / 997 / Boxster / Cayman

    SKU:ER2180002

    In Stock In Stock
    Lowered 966/997 run out of rear toe adjustment range. Our Adjustable rear toe links extend the range of adjustment and add bump steer correction. Adjustable Length - Threaded double adjuster for easy toe settings. Angled head - Lower the car and the toe links angle down. This shifts the ball stud from its center and limits the available range of articulation. We solve this problem by angling the head to move the stud back towards the center of its range of articulation at static ride height. Bump steer adjustable - The built in bump steer adjustment lets you dial in a minimal bump steer curve. Fully weather sealed - Proper boots at both the ball joint and heim joint ends to keep water and contaminant out for extended life. Set comprises of 2 links.
    £742.50 inc VAT £618.75 ex VAT
  • RSR Spec Rear Toe Control Arm Kit. All Models. 1997 to 2012

    SKU:SR082

    In Stock In Stock
    Precision alignment and bump steer set up are critical for good handling, these RSR spec Rear Toe Control Arms are fabricated to exacting tolerances and standards, provide the premier upgrade for your track or street car. Using aerospace quality rod ends and components to provide for the most durable, accurate part available. With a left and right hand double adjuster the RSR toe link allows for extremely precise and infinite adjustment to fine tune suspension settings. Also included are seals to protect the monoballs in exposed environment. Sold p/pair Fits all Models; 996, 997, Boxster, and Cayman 1997 to 2012
    £643.45 inc VAT £536.21 ex VAT
  • RSR Spec Rear Control Arm Lock Out Plate Kit. All Models 1997 to 2012

    SKU:SR084

    3-5 Days 3-5 Days
    These precision machined stainless steel RSR Spec plates provide a sure lock to eliminating unwanted camber changes caused by the factory eccentric moving under load. By bolting these plates to the chassis on the inboard end of the Rear control arm, the control arm will now be held in a constant, fixed position. Ideal when using RSR Spec Rear Control arms. Fits all Models; 996, 997, Boxster, and Cayman 1997 to 2012
    £93.49 inc VAT £77.91 ex VAT
  • GT3 Split Wishbone Ball Joint Front & Rear 1999-2012 GT3RS Cup & RSR

    SKU:1986

    In Stock In Stock
    OEM Wishbone Coffin Arm Front & Rear Applications. For All GT2 / GT3 RS. Also Motorsport Applications; on Boxster 996 & 997. Note. Handed so please denote Left or Right on ordering.
    £199.99 inc VAT £166.66 ex VAT
  • SPAX Lowering Spring Kit 996 C2 / 997 C2 / C2S 1998-2012 (set of 4)

    SKU:7502

    3-5 Days 3-5 Days
    Set of 4 lowering springs for 996/997 C2 Models 1998 to 2012. SPAX spring kits are progressively wound. This offers a softer ride at low speeds & a stiffer ride at high speeds, when you need it most. Also fits Early 996 C4 1998 -2001 Models
    £249.95 inc VAT £208.29 ex VAT
  • Elephant Racing Bump Steer Adjustable Front Track Rod Ends for Lowered Cars 996 / 997 / Boxster / Cayman

    SKU:ER2180008

    In Stock In Stock
    Correct geometry for lowered cars with bump steer adjustment and angled head. Bump steer adjustable - The built in bump steer adjustment lets you dial in a minimal bump steer curve. Angled head - Lower the car and the tie rods angle down. This shifts the ball stud from its center and limits the available range of articulation. We solve this problem by angling the head to move the stud back towards the center of its range of articulation at static ride height. Fully weather sealed - Proper boot at the ball stud to keep water and contaminant out for extended life. Set comprises of 2 links.
    £544.50 inc VAT £453.75 ex VAT
  • 996 / 997 GT2 & GT3 RSR Control Arm Monoball Bush Kit for Front & Rear OEM Outer

    SKU:SR040

    In Stock In Stock
    Whether for a dedicated race car, or for a suspension upgrade on your road car, these RSR inner control arm monoballs are the ultimate upgrade or replacement. CNC machined from aircraft quality aluminium, the housing contains the BEST aerospace monoball available. Stainless steel bushings, and K nuts complete the package. Ideal when upgrading any 996, 997, Boxster or Cayman to track focused set up work. OEM outer control arms & shims also available. Price per pair
    £384.95 inc VAT £320.79 ex VAT
  • 996 / 997 GT2 & GT3 RSR Control Arm Monoball Bush Kit for Front & Rear OEM Outer

    SKU:SR083

    In Stock In Stock
    Made from the highest quality aerospace materials, the RSR spec Track rod bump steer kit will allow for precise adjustment ranging from moderate street lowering to the most aggressive race setup. These kits allow for infinite fine tuning and come complete. No other hardware or parts needed. Includes seals. Fits all Models; 996, 997, Boxster, and Cayman 1997 to 2012
    £384.95 inc VAT £320.79 ex VAT
  • Front Top Mount 997 C4 / C4S & 997 Turbo LEFT 2005-2012

    SKU:11357

    In Stock In Stock
    OEM Top Mount for all 4 wheel drive cars only. Handed
    £85.99 inc VAT £71.66 ex VAT
  • EuroCupGT Uprated Track Rod End / Steering Control Arms All 1997-2012

    SKU:7375

    In Stock In Stock
    Fits all 996 / 997 / Boxster / Cayman models 1997 to 2012. Ideal Steering performance upgrade for both Road & Track, fine adjustment & robust design with sealed joints. (pair)
    £149.94 inc VAT £124.95 ex VAT
  • Stomski Racing Rear Adjustable Toe Link Kit All Models 1997-2012

    SKU:AP997240

    In Stock In Stock
    Stomski Racing Motorsport quality Billet Alloy & rose Jointed Toe Arms. Adjust your camber & re dial in the rear toe. These adjustable links are design to give you a more responsive rear end along with the ability to dial in the toe on the rear end more precisely by allowing you to keep the arms parallel. Fits all Models inc GT3 RS, Cup & Turbo models 1997 -2012
    £462.00 inc VAT £385.00 ex VAT
  • Elephant Racing Upper Rear Adjustable Track Rod Set for Lowered Cars 996 / 997

    SKU:ER2180003

    In Stock In Stock
    Adjustable rear track rods eliminate the compliant rubber bushings and allow adjustment of track width and kinematic toe. Adjustable Length - Threaded double adjuster makes it easy. Heim Joint - Spherical bearing type heim joint instead of the compliant rubber bushing in OEM track rods for superior driving precisoin. Fully weather sealed - Proper boots at both heim joint ends to keep water and contaminant out for extended life. Set comprises of 4 links.
    £1,485.00 inc VAT £1,237.50 ex VAT
  • RSR Spec Rear Upper Control Arm Kit ( set of 4 ) All 996 and 997 Models 1998-2

    SKU:SR086

    In Stock In Stock
    These RSR Spec Rear Upper Control Arms direct replacements for the factory cast alloy part & improve the stability of the rear handling of the car. They provide for better tyre wear, improved tyre contact surface, and better range of suspension setups which all leads to a better handling or faster lap times. Using aerospace quality rod ends and components to provide for the most durable, accurate setup available. With left and right hand threads the Control Arm Link kit allow for precise infinite adjustability and ease of setting. Also included are seals to protect the monoballs in exposed conditions. Kit fits All 996 and 997 Models; 1998-2012
    £874.49 inc VAT £728.74 ex VAT
  • H&R Lowering Spring Kit 996 / 997 C2 & C2S 1998-2012 (per pair)

    SKU:2356

    3-5 Days 3-5 Days
    High quality Smooth & progressive. All 2 wheel drive models
    £299.99 inc VAT £249.99 ex VAT
  • GT3 Adjustable Front Anti Roll Bar Kit 997 All

    SKU:997GT3BAR

    3-5 Days 3-5 Days
    For a perfect fit, reliability you can depend on, fully adjustable with four positions available, & optimum performance, the factory GT3 swaybar is the best on the market. The light weight hollow 26.8mm OD sway bars are half the weight of a solid bar with the same stiffness. Fits Boxster 2005- & Cayman plus All 997 models. Includes Bushes
    £300.32 inc VAT £250.27 ex VAT
  • Elephant Racing Litronic Bracket Kit for GT3-R Type Control Arms

    SKU:ER2180009

    3-5 Days 3-5 Days
    Litronic adapter to attach litronic sending unit to GT3-R type control arms. Order 1 kit per pair of GT3-R type control arms.
    £49.50 inc VAT £41.25 ex VAT
  • 997 GT3 RSR/Cup Control Arm Monoball Bush Kit Front/Rear OEM Outer Control Arms

    SKU:SR049

    3-5 Days 3-5 Days
    Similar to our SR040, these Control Arm Monoballs are 17mm wider for applications where you need greater range. Use these Monoballs on 997 GT3 or Cup cars, or on other setups requiring more adjustment. Whether for a dedicated race car, or for a suspension upgrade on your street GT3, these inner Control Arm Monoballs are the ultimate upgrade or replacement. CNC machined from aircraft quality aluminum, the housing contains the BEST aerospace monoball available. Stainless steel bushings, and Jet nuts complete the package to make these assemblies your only choice for upgrading or replacement. Seals are included for the ultimate upgrade. Ideal when upgrading any 996, 997, Boxster or Cayman to track focused set up work. OEM outer control arms & shims also available. Price per pair
    £458.09 inc VAT £381.74 ex VAT
  • EuroCupGT Adjustable Tension Control Arms 996 Fr & Re / 986 Front & 997 Rear

    SKU:EURO6435

    In Stock In Stock
    EuroCupGT uprated suspension tension bars replace the cast aluminium arms & allow for neutral adjustment when setting up your cars geometry. The rubber bushing is replaced with a Rose Joint to allow for more accurate handling. Fits the following: All 996 Models inc GT3 & Turbo Front & Rear All Boxster 986 Front Only All 997 Models inc GT3 & Turbo Rear Only
    £293.81 inc VAT £244.84 ex VAT